MWSC FAQs: Clutch and Driveline
Posted by Devin Daniels on
Can I build my own clutch through you guys?
Yes, we make it easy for you. Come up with a custom 6 digit part number by selecting the components you desire in your clutch. Simply follow these steps:
I’m new to pulling and need to update my clutch, what should I know?
If you’re entering a stock class, you may only need a new disc (our MWSC Kevlar Disc # 51155) and possibly a heavier spring for your existing clutch. The stock spring is a 300# spring, while the heavy duty spring (red in color) is an 800# spring (See our Beginner Clutch Package on page 14 in our 2019 catalog).
Why is it recommended to replace my stock pressure plates?
Although your stock pressure plates might not need to be replaced, they’re made of a thin material that tends to warp when used in pulling. Check the stock plates to make sure they’re completely flat; if they’re not they can be trued or replaced with our MWSC Pressure Plates (page 14 in our 2019 catalog), which are made from billet metal making them less likely to warp.
How far does the spring need to be compressed?
Our MWSC red and yellow springs are each 6” long, they need to be compressed to 4-½”.
Why is the Heavy Duty Release Arm necessary?
This part will make it easier to press down on the clutch pedal when using one of our heavier springs. We have three styles available: the narrow, wide, and 82 Series, all of which are longer and stronger than the stock arms (page 14 in our 2019 catalog).
Is it necessary to use the Teaser Spring?
Our Teaser Spring makes for a smoother engagement and allows you to feel when the clutch is engaging. We install one in every clutch assembled (page 13 in our 2019 catalog).
How do I know if my clutch is “running true”?
When the clutch is installed and the engine is turned OFF, measure the distance between the disc and the #3 or #6 lug driver in five or six spots - the measurements should be the same. If they’re not the same, shims will be needed on one side of the motor until measurements are all equal.
Which clutch should be used for a pro stock tractor?
You’ll need the Metallic Disc with four or five pucks on each side (page 14 in our 2019 catalog); along with this you will need our 1150# spring (yellow in color). This also requires replacing the stock drive shaft. (Note: If you use the four or five puck disc mentioned above, you will also need to replace the clutch driver to our MWSC Six Lug Aluminum Clutch Driver and replace the pressure plates.)
Which driveshaft works with an 82 Series tractor?
The 82 Series is a wide frame, but because these were made with a rubber boot coupler, the length of the driveshafts all vary. We make a driveshaft 24” long (page 13 in our 2019 catalog); when placing an order for one of our driveshafts you must specify which disc you plan on using: Metallic or Kevlar (page 14 in our 2019 catalog).
Although the front two holes in our MWSC shaft come pre-drilled, the rear hole will need to be drilled after determining the correct length. If you have our MWSC 3” Coupler (page 13 in our 2019 catalog) it may be used as a drill guide. Be sure to use coolant when drilling and keep in mind each hole is a weak spot in the driveshaft, so “measure twice to cut once”.
Standard length for a narrow frame tractor is 18-¼” and wide frame is 19-¼”.
The spring is held in place by a Split Collar (page 13 in our 2019 catalog); one split collar is used behind our 800# red spring, whereas two split collars are used behind our 1150# yellow spring.
Why use a Center Support Bearing # 52123?
A Center Support Bearing # 52123 (page 13 in our 2019 catalog), or pillow block bearing, is necessary in tractors running at or above 4000 RPM. When the clutch turns at a higher RPM, the driveshaft is also moving in a small circular motion; the Center Support Bearing # 52123 helps eliminate some of this circular motion. (It also helps with some misalignment issues.)
What are the differences between the Regular Metallic Disc # 52124, the Heavy Duty Metallic Disc # 52125, and the Super Heavy Duty Metallic Disc # 52126?
The Regular Metallic Disc # 52124 has 3 pucks on each side and it measures the same as the stock pieces.
The Heavy Duty Metallic Disc # 52125 has 4 pucks on each side and measures 6-½”.The pressure plates and six finger driver also have a larger diameter.
The Super Heavy Duty Metallic Disc # 52126 has 5 pucks on each side and measures 7”. The pressure plates and six finger driver also have a larger diameter.
There is a chart for HP and disc size on page 13 in our 2019 catalog.
Yes, we make it easy for you. Come up with a custom 6 digit part number by selecting the components you desire in your clutch. Simply follow these steps:
- The first number will always be 8
- For the second number, put 1 for a complete clutch without a 6 pin driver, and 2 for a complete clutch with a 6 pin driver
- In the third number you’ll specify your desired disc: 1 for Kevlar Disc, 2 for 3 puck, 3 for 4 puck, and 4 for 5 puck
- In the fourth number you’ll specify the release arm of your choice: 1 for narrow frame, 2 for wide frame, and 3 for 82-Series
- For the fifth number, you’ll choose a spring: 1 for our red spring (800#), and 2 for our yellow spring (1150#).
- For the sixth and final number, you’ll specify a driveshaft: 1 for narrow, 2 for narrow with a “coupler, 3 for wide, 4 for wide with a 3” coupler, and 5 for the 24” shaft for an 82-Series with no rear hole.
I’m new to pulling and need to update my clutch, what should I know?
If you’re entering a stock class, you may only need a new disc (our MWSC Kevlar Disc # 51155) and possibly a heavier spring for your existing clutch. The stock spring is a 300# spring, while the heavy duty spring (red in color) is an 800# spring (See our Beginner Clutch Package on page 14 in our 2019 catalog).
Why is it recommended to replace my stock pressure plates?
Although your stock pressure plates might not need to be replaced, they’re made of a thin material that tends to warp when used in pulling. Check the stock plates to make sure they’re completely flat; if they’re not they can be trued or replaced with our MWSC Pressure Plates (page 14 in our 2019 catalog), which are made from billet metal making them less likely to warp.
How far does the spring need to be compressed?
Our MWSC red and yellow springs are each 6” long, they need to be compressed to 4-½”.
Why is the Heavy Duty Release Arm necessary?
This part will make it easier to press down on the clutch pedal when using one of our heavier springs. We have three styles available: the narrow, wide, and 82 Series, all of which are longer and stronger than the stock arms (page 14 in our 2019 catalog).
Is it necessary to use the Teaser Spring?
Our Teaser Spring makes for a smoother engagement and allows you to feel when the clutch is engaging. We install one in every clutch assembled (page 13 in our 2019 catalog).
How do I know if my clutch is “running true”?
When the clutch is installed and the engine is turned OFF, measure the distance between the disc and the #3 or #6 lug driver in five or six spots - the measurements should be the same. If they’re not the same, shims will be needed on one side of the motor until measurements are all equal.
Which clutch should be used for a pro stock tractor?
You’ll need the Metallic Disc with four or five pucks on each side (page 14 in our 2019 catalog); along with this you will need our 1150# spring (yellow in color). This also requires replacing the stock drive shaft. (Note: If you use the four or five puck disc mentioned above, you will also need to replace the clutch driver to our MWSC Six Lug Aluminum Clutch Driver and replace the pressure plates.)
Which driveshaft works with an 82 Series tractor?
The 82 Series is a wide frame, but because these were made with a rubber boot coupler, the length of the driveshafts all vary. We make a driveshaft 24” long (page 13 in our 2019 catalog); when placing an order for one of our driveshafts you must specify which disc you plan on using: Metallic or Kevlar (page 14 in our 2019 catalog).
Although the front two holes in our MWSC shaft come pre-drilled, the rear hole will need to be drilled after determining the correct length. If you have our MWSC 3” Coupler (page 13 in our 2019 catalog) it may be used as a drill guide. Be sure to use coolant when drilling and keep in mind each hole is a weak spot in the driveshaft, so “measure twice to cut once”.
Standard length for a narrow frame tractor is 18-¼” and wide frame is 19-¼”.
The spring is held in place by a Split Collar (page 13 in our 2019 catalog); one split collar is used behind our 800# red spring, whereas two split collars are used behind our 1150# yellow spring.
Why use a Center Support Bearing # 52123?
A Center Support Bearing # 52123 (page 13 in our 2019 catalog), or pillow block bearing, is necessary in tractors running at or above 4000 RPM. When the clutch turns at a higher RPM, the driveshaft is also moving in a small circular motion; the Center Support Bearing # 52123 helps eliminate some of this circular motion. (It also helps with some misalignment issues.)
What are the differences between the Regular Metallic Disc # 52124, the Heavy Duty Metallic Disc # 52125, and the Super Heavy Duty Metallic Disc # 52126?
The Regular Metallic Disc # 52124 has 3 pucks on each side and it measures the same as the stock pieces.
The Heavy Duty Metallic Disc # 52125 has 4 pucks on each side and measures 6-½”.The pressure plates and six finger driver also have a larger diameter.
The Super Heavy Duty Metallic Disc # 52126 has 5 pucks on each side and measures 7”. The pressure plates and six finger driver also have a larger diameter.
There is a chart for HP and disc size on page 13 in our 2019 catalog.
HIRE ALPHA RECOVERY EXPERTS TO FIX YOUR CREDIT SCORE.
I can’t express how glad I feel after working with Alpha Recovery Experts. I’d been dealing with an eviction on my credit report, which made it extremely difficult to obtain housing. After reaching out to them, they promised to assist, and I was astounded by how quickly they responded.
They eliminated the eviction and other negative items from my credit report within a few business days. I saw my credit score increase to 1099, which seemed like a dream come true. Thanks to their help, I finally feel optimistic about my future and can hunt for housing without the weight of my past holding me back.
Contact info;
Email: ( Alpharecoveryexpert@consultant.com )
WhatsAp: ( +44,745,742 4681 )
HIRE A HACKER YOUR STOLEN CRYPTO RECOVERY / BTC / USDT / ETH WITH THE HELP OF CAPITAL CRYPTO RECOVER.
I want to share my experience publicly regarding cryptocurrency wallet recovery, I highly recommend you to contact CAPITAL CRYPTO RECOVER, a professional private investigator in the Bitcoin world. They have a certified expert security team specializing in Bitcoin Recovery Services and have helped many people worldwide recover their lost funds. My wife and I were defrauded by an online manipulator posing as an experienced crypto investment professional. We lost $9.2 Million Stolen BTC in cryptocurrency and were left feeling homeless. After spending hours searching for a reliable crypto recovery service, I discovered CAPITAL CRYPTO RECOVER online. By patiently explaining my situation to their team, I was able to recover all my funds. Remarkably, my money was returned to my wallet in less than 24 hours. I am extremely grateful to CAPITAL CRYPTO RECOVER for their excellent assistance—they truly were a godsend in my difficult situation. If you have fallen victim to a cryptocurrency scam, you can reach CAPITAL CRYPTO RECOVER through the following channels Email: Recoverycapital@fastservice.com OR Call/Text: +1 (336) 390-6684 Contact: Capitalcryptorecover@zohomail.com Website: https://recovercapital.wixsite.com/capital-crypto-rec-1
HIRE A HACKER TO RECOVER LOST OR STOLEN BITCOIN/CRYPTO – ALPHA RECOVERY EXPERTS.
I never expected to retrieve my lost cryptocurrency worth $249,200, but all thanks to Alpha Recovery Experts for their excellent recovery service. I had read an advertisement online about how I could double my savings using an investment platform. I became fascinated and deposited my savings there. Everything went bad when I realized it was all a hoax. I phoned a friend, who encouraged me to seek assistance from a crypto recovery expert. Alpha Recovery Experts were always regarded as the leader and most trustworthy specialist to consult. I contacted them, and they worked wonders on my case. I strongly recommend Alpha Recovery Experts for all Crypto Recovery services.
Email; Alpharecoveryexpert@consultant.com
Website; Alpharecoveryexpert. com
Call or Text +44(745)742-4681
Buy Caluanie Muelear oxidize & Red Mecury WhatsApp: +447401473736
Caluaine Muelear Oxidize is one of the most demanded products in the metal or chemical processing sector, This product is used for crushing and processing precious metals and semi-precious stones. It is used for processing precious and semi-precious stones, crushing metals in the chemical industry. this makes it easier to break nails with bare hands after 10-20 seconds of immersion. Heavy water changes the properties of the metal, making it brittle. But at the moment of evaporation of heavy water, the rock returns to its previous state.
Caluanie Muelear oxidize, made in America. our company has an exclusive contract for the supply of Caluanie in USA and Worldwide.
-Type: caluanie muelear oxidize
-Density: 1600 g / l and 1.944 g
-Weight: 1650 g / l 1900 g
-Manufacturer: USA,
-Expiry date: no expiration date
-Characteristics: Embrittlement of metals does not interact with other chemical components
-Do not burn your hands
-Designed for reusable use
-Shipping: Worldwide Delivery
CONTACT IF INETERESTED
We supply other chemicals as well such as SSD, MECURY,
Mercury metal (from latin hydrargyrum = liquid silver) is shiny and silvery and the only metal that is liquid at room temperature. Mercury metal is known since ancient times, when it was believed to be something magical and also a cure for everything. More recently Mercury metal was and still is used in thermometers and barometers and in amalgams as filling for our teeth. Elemental mercury and many of its compounds are very toxic, so it should be avoided and not be used, if there are alternatives. Mercury metal can be sold only in small quantities and perfectly sealed for laboratory or display use. CONTACT IF INTERESTED
Contact Information
Telegram: @Ranko3222
WhatsApp: +447401473736
https://toprapidsolution.blogspot.com/
How to Recover Your Crypto Investments from Scammers / Alpha Recovery Experts
ALPHA RECOVERY EXPERTS centers their expertise on financial fraud and ethical hacking services, focusing much of its resources in fighting binary options scams. They have adequate technological and financial expert professionals who have taken giant strides in helping clients recover their funds while maintaining discretion and utmost confidentiality. ALPHA RECOVERY EXPERTS boast of a team of recovery experts who are experienced in binary options and another cryptocurrency recovery. If you have unfortunately lost your funds to a Crypto scam, all is not lost. The ALPHA RECOVERY EXPERTS’s team is ready to help you retrieve your lost or stolen Cryptocurrency.
Contact Information
Email Add; Alpharecoveryexpert@consultant. c om
WhatsApp; +44(745)742-4681.
Homepage; alpharecoveryexperts. co m